Horizontal injection press

Control unit
Based on the data of Japanese star novel high speed and high precision control of the main pressure requirements all within the monitoring, all available in your hands, high degree of automation of the machine and fully guarantee the you need products stable and precise forming requirement;
The main action units are controlled by Italy electronic scale and pressure sensor.
 Injection unit
The design of single cylinder injection. Oil pressure cylinder and the circuit board into one, in addition to a substantial reduction of oil spills, and to reduce the response delay time.
Low speed and high torque hydraulic motor control screw drive, feeding and stability, injection pressure from the sensor feedback to achieve semi closed precision control, thus ensuring accurate shooting
 
Locking element
The design of direct pressure clamping, clamping force can be fully and evenly distributed;
The hydraulic system uses the high precision servo system, with the special oil circuit and the hydraulic oil tank circuit design, to ensure the low energy consumption and fast action;
Hydraulic lock mould system is equipped with a pressure sensor, the realization of the high precision semi closed control, low pressure mold protection, and protect mold position very short (by a semi closed valve and a pressure sensor for Disease Control), because of the precision of high-pressure position so it can saving time pressure and without special mould adjusting, you only need to easily in the computer setting a low voltage lock mode position can be automatic calculation of pressure, clamping position with high repeatability.
Other
The suction nozzle is the self sealing type magnetic suction strainers, ensure the cleanliness of hydraulic oil. If the cartridge is pollution and blockage of oil to the mouth of the vacuum degree is 0.018Mpa will be issued an alert
The allocation of oil temperature alarm device, when the oil temperature exceeds the maximum value when the alarm signal and automatically shutdown; 

project	Company	TS120			TS200			TS250			TS320			TS650
Injection unit
Screw diameter	mm	32	36	40	40	45	50	45	50	56	50	56	65	72	80	90
Injection capacity	cm3	101	127	157	289	366	452	390	481	603	481	603	813	1507	1861	2356
Injection weight(P.S)	g	95	120	148	273	346	427	368	455	570	455	570	768	1424	1759	2226
Injection pressure	kgf/cm2	2670	2110	1709	2628	2076	1682	2353	1906	1519	2527	2015	1495	2042	1654	1307
Length/Diameter ratio	L/D	20.6	18.3	16.5	21.5	19.1	17.2	20.6	18.5	16.5	21.6	19.3	16.6	24.3	21.9	19.4
Injection speed	mm/sec	150			150			150			150			150
Injection rate	cm3/sec
Screw speed	rpm/sec	121	153	188	238	294	257	238	294	369	294	369	499	610	754	950
Plasticizing capacity(P.S)	kg/hr	188			164			160			142			115
Hopper capacity	KG	33	45	62	62	84	115	66	102	132	82	131	167	182	256	325
		25			50			100			100			100
Clamping unit
Mold clamping force	Ton	120			200			250			450			650
Mold opening force	Ton	3.8			6.5			9.1			19.8			21
Mold clamping stroke	mm	465			610			710			960			1260
Min.mold thickness	mm	180			200			220			260			390
Max.mold thickness	mm
Distance between tie bars	mm	645			810			930			1220			1650
Ejector force	Ton	370*370			470*470			520*520			670*670			910*910
Ejector stroke	mm	3.4			8.8			8.8			13.7			15
Ejector quantity	P.C.S.	150			150			200			200			250
		5			5			5			13			21
Other
Heater band capacity	KW	7.65			9.45			11.25			18.3			33
No.of heating zones	Zone	Nozzle+3			Nozzle+3			Nozzle+3			Nozzle+4			Nozzle+4
Electric motor	KW	11			15			22			30			75
Oiltankcapacity	L	265			390			416			590			1000
Machineweight	Ton	3.5			5.8			7.4			12.4			24.8
Machinedimension(L*W*H)	mm		3.8*1.02*1.46		4.96*1.14*1.53			5.5*1.24*1.74			6.53*1.53*1.81			9.6*2.1*2.31